water filter systems.
The WFS Series Water Filter Systems are designed to handle high volumes of wash water such as produced by car or truck washes. These completely automatic treatment units will collect your dirty wash water and process it so that it can be reused in the washing operation.
The WFS draws the wash water from your collection sump and transfers it to the holding and collection tank. The solids separator removes much of the heavy sand and grit and deposits it in the collection container for disposal. Additional solids which settle in the holding tank are also deposited in the collection container. The Filter System not only cleans the water, but also adds an oxidizer reagent to kill bacteria and odors. The oxidizer is used to make the water more environmentally friendly and less hazardous for personnel doing the washing. Rinsing normally uses fresh water which is collected with the wash water. Any excess water can be automatically disposed of as treated water, more easily achieving compliance with environmental regulations. Water filter systems are applicable to brush type car, truck and bus washing operations, which typically require higher volumes of water, but not of the quality with the WRS systems produce. The WFS 42, which includes 5 micron final filtration. can also be used for pressure washer applications when cost is especially critical. An automatic degassing oxidizer pump is included as well as high capacity permanent element filtering. A fresh water rinse is required for many applications. The water quality is better than from most similar systems available from other suppliers. |
products
Water Filter System 72
Rated flow: 24 gpm (35000 gpd) Electrical requirement: 115 VAC, 60 Hz, 1 phase, 15 amp total Feed pump: 1/3 HP self priming centrifugal cast iron with thermally protected motor Discharge pump: 1/2 HP cast iron with thermally protected motor. Supplies pressurized water to car or truck wash, or other use. Electrical controls: GFCI provided. Pre-wired with 15 amp plug, 10 ft. cord, Power switch, lighted, NEMA 4 rated enclosure Oxidizer metering pump: Electronic controlled diaphragm pump with stroke rate and stroke length controls and automatic degassing head. Injects oxidizer reagent in water to disinfect and deodorize Holding and collection tanks: 1000 gallon polyethylene conical bottom tank. With inlet, outlet, and solids discharge piping. Centrifugal solids separator: Removes heavy solids (sand and grit) prior to filter system and delivers them to a holding container for disposal. Filter system: High capacity permanent element filter system with automatic backwash. Make up water: Flow as required for application, 100 psi maximum pressure Connection sizes: Feed pump inlet- 1 1/2 NPT, Treated water outlet- 1 NPT. Make up water- 1/2 NPT Overall dimensions: Tank 6 ft. diameter, 7 ft. tall, Control and pumping module 4 ft. long, 2 1/2 ft wide Module includes pumps, controls, solids separator, filter system. Shipping weight: 700 pounds approximate Options: Additional water storage capacity. pH adjustment system. Activated carbon water polishing system. Ozone treatment. Pretreatment systems, oil skimmers, oily water separators. Custom modifications available. Water Filter System 42
APT-4-P OILY WATER SEPARATOR SPECIFICATIONS Rated flow :4 gpm (5800 gpd) Principle of operation: Oily water separation to 15 ppm via enhanced gravity and large coalescer bed. Capacity: Oils with up to .96 specific gravity, 0 to 100% concentration. Temperature 33 to 120F degrees ambient. Suction: 25 ft. maximum vertical suction lift, less than 15 ft recommended. Discharge pressure: 15 psi at 4 gpm, 50 psi maximum at 2 gpm. Oil: 30 ft. maximum vertical discharge, 3 gal. approximate per batch. Tank construction: PVC material, continuously welded. Internals: Single, large coalescer bed, polypropylene beads. Electrical requirement: 115 VAC, 60 Hz, 1 phase. 15 amp protected circuit. Pump: Model 332 progressive cavity pump. Motor: 1/2 hp, 1750 rpm, TEFC Valves: Bronze solenoid, gate, pressure relief (30 psi) Pipe: Brass with NPT threads. Controls: JIC enclosure, dielectric interface sensor with 2 tip sensitive probes. Connection sizes: Inlet 1 1/4 NPT, Backflush recirculate 3/4 NPT, Oil Discharge 3/4 NPT, Blackflush inlet 3/4 NPT, Blackflush water 30 psi maximum Overall dimensions Less than 27″ x 27″ x 40″ tall Weight Dry 270 lbs. Wet 360 lbs. |
Water Filter System 92
Rated flow: 50 gpm (72000 gpd) Electrical requirement: 230 VAC, 60 Hz, 1 phase, 20 amp total Feed pump: 3/4 HP self priming centrifugal cast iron with thermally protected motor. Discharge pump: 1 1/2 HP cast iron with thermally protected motor. Supplies pressurized water to car or truck wash, or other use. Electrical controls: Pre-wired with 20 amp plug, 10 ft. cord Power switch, lighted, NEMA 4 rated enclosure Oxidizer metering pump: Electronic controlled diaphragm pump with stroke rate and stroke length controls and automatic degassing head. Injects oxidizer reagent in water to disinfect and deodorize Holding and collection tanks: Two 1000 gallon polyethylene conical bottom tanks. With inlet, outlet, and solids discharge piping. Centrifugal solids separator: Removes heavy solids (sand and grit) prior to filter system and delivers them to a holding container for disposal. Filter system: High capacity permanent element filter system with automatic backwash. Make up water: Flow as required for application, 100 psi maximum pressure Connection sizes: Feed pump inlet- 1 1/2 NPT, Treated water outlet- 1 1/2 NPT, Make up water- 1/2 NPT Overall dimensions: Two tanks 6 ft. diameter, 7 ft. tall, Control and pumping module 4 ft .long, 2 1/2 ft. wide Module includes pumps, controls, solids separator, filter system. Shipping weight: 1100 pounds approximate Options: Additional water storage capacity. pH adjustment system. Activated carbon water polishing system. Ozone treatment. Pretreatment systems, oil skimmers, oily water separators. Custom modifications available. |